Austin, TX · $39 Diagnostic · One verified pro

Washer Repair in Austin, TX

Broken washer? Don't guess. We provide expert diagnosis and repair across Austin, TX. Book online to save on the service call.

  • Diagnostic drops to $39 as you complete the steps.
  • Typical repair time: 1-2 hours.
  • Typical labor range: $110-$219 (labor only, parts extra).
  • Coverage: 78701, 78702, 78703, 78704, 78705, 78745, 78758, 78759, 78729, 78748 and nearby areas.

Recent Washer Repair Repairs in Austin

Real recent repair cases. Prices shown are from past completed jobs.

Top verified matches for Washer Repair in Austin.

AustinJan 13, 2026VERIFIEDREPAIRED

LG • Model WT7600HKA

$268
Parts + Labor
!
Issue

Appliance type: Top-Load Washing Machine Brand: LG Issue Type: Water Leak / Inlet Valve Failure Customer Complaint The customer reported that water was continuously dripping into the washer drum even when the washing machine was turned off and not in use.

Fix

The faulty water inlet valve assembly was removed and replaced with a new OEM-compatible inlet valve assembly. Post-Repair Testing After the replacement, the washer was tested through multiple fill and wash cycles. No water leakage was observed All inlet valves operated correctly The unit shut off water supply completely when not in use Final Result The issue was fully resolved. The washing machine is now operating normally with no water entering the drum when powered off.

Parts:

LG Washer repair photo
+ 2 more photos
Cedar ParkDec 29, 2025VERIFIEDREPAIRED

GE • Model GTW500ASN0WS

$269
Parts + Labor
!
Issue

The customer reported that their top-load washer was not filling with enough water during the wash cycle. When the washer was loaded with a larger amount of laundry, the unit frequently went into an out-of-balance condition and failed to complete the cycle properly.

Fix

The technician replaced the worn suspension spring rods to restore proper tub stability and eliminate the out-of-balance condition. Additionally, the accelerometer (speed/load sensor) was replaced to ensure accurate load detection and correct water level adjustment during wash cycles. After completing the repairs, the washer was fully tested under normal operating conditions. The unit filled with the correct amount of water, remained stable during operation, and no further issues were observed. Warranty for labor and patrs - 90 days

Parts:

GE Washer repair photo
+ 2 more photos

* Prices shown are from past completed jobs and include parts and labor. Actual repair cost varies by model, diagnosis, and part availability.

Why choose GoFindTech in Austin?

We focus on one thing: sending a single, verified technician to your home in Austin, instead of blasting your request to dozens of companies. That means fewer spam calls and a faster repair.

If you're in zip codes 78701, 78702, 78703, 78704, 78705, 78745, 78758, 78759, 78729, 78748, our techs are already working in your neighborhood. Most washer repairs are completed in 1-2 hours with transparent pricing and a clear diagnostic.

Common washer problems we fix in Austin

These are common washer symptoms we diagnose in Austin, TX. We confirm the exact cause during the diagnostic before any repair.

Not Draining

If the cycle ends with standing water, the washer is usually blocked, the pump is failing, or the drain path has an obstruction.

  • Check drain filter / coin trap for blockage
  • Inspect drain hose for kinks or clogs
  • Test drain pump for power and operation

Quick tip: Check the drain hose behind the washer for kinks. If your model has a drain filter/coin trap, clean it (have towels ready).

Learn more →

Not Spinning

No-spin is often related to the lid/door lock system, a worn drive component, or an out-of-balance protection trigger.

  • Test lid/door lock switch and wiring
  • Check belt (if applicable) for wear/slip
  • Inspect drive motor / coupler / clutch (by design)

Quick tip: Redistribute the load and try a spin-only cycle. If the washer is severely off-balance, it may refuse to spin for safety.

Learn more →

Leaking Water

Leaks can come from hoses, the pump, the tub seal, or the door boot (front-load). The source matters — we confirm it during the diagnostic.

  • Inspect hot/cold inlet hoses and valve body
  • Check drain hose connections and standpipe height
  • Inspect pump housing for cracks/leaks

Quick tip: Turn off both water supply valves and check the inlet hoses for dripping at the wall and at the washer connection.

Learn more →

Making Loud Noise

Noise can be caused by worn bearings, loose objects, failing suspension/shocks, or a drive component under load.

  • Check for loose objects between tub and basket
  • Inspect shocks/suspension rods for wear
  • Test spin for bearing noise and basket play

Quick tip: Run a short spin cycle empty. If it’s still loud, it’s likely mechanical (bearings/suspension) rather than the load.

Learn more →

Won't Start

A washer that won’t start is often caused by a door/lid lock issue, power problem, or a control failure — not always a bad motor.

  • Verify outlet power and breaker/GFCI
  • Test lid/door lock system and strike alignment
  • Check user interface / control board response

Quick tip: Make sure the door/lid is fully closed and latched. If it’s a GFCI outlet, reset it and try again.

Learn more →

Washer Repair brands we service in Austin

We handle most major household brands — from popular Samsung and LG to Whirlpool, GE and more.

FAQ about washer repair in Austin

How much does washer repair cost?

Most jobs in Austin fall into the $110-$219 labor range. Parts are quoted separately once the technician confirms the exact failure during the diagnostic.

How fast can you come out?

Same-day or next-day visits are usually available for most zip codes in Austin. When you complete the wizard above, you'll see available time windows before you confirm.

Is it worth fixing an older unit?

During the diagnostic, the technician will estimate the total repair cost and compare it to the age and condition of your washer.